A nylon brush strip seal with an anodised aluminium carrier that mounts to the inside or outside of a door. It is ideal for sliding or double acting doors. Can be concealed inside of an aluminium door suite bottom rail by the fabricator. Used in conjunction with Raven threshold plates. Location: Bottom of single, double, sliding and double acting doors. Min/Max Gap: Up to 19mm (user determined). Finish: Satin clear (silver), bronze anodised aluminium (15µm) or paint at extra cost. Fixing: Self adhesive or can be screw fixed. Note: Contact surface must be clean, smooth and if painted, well cured. Self adhesive seals will not adhere to oiled or alkyd finishes or to easy clean wash and wear paint surfaces. Seal: Black fine, dense, UV stabilised nylon filaments. Sizes: Available in stock lengths. Approvals Energy NCC Pt. 3.12.3.3 & J3.4.

A cam activated, lifting action, automatic door bottom seal. It is quick and easy to install without cutting or removing the door and uses concealed fasteners. This DIY product has been granted an Australian Design Award. Ideal for residential and light commercial applications such as motels and retirement villages. Can be used in conjunction with Raven threshold plates. Location: Bottom of single inward opening butt hinged doors. Min/Max Gap: 3mm to 16mm. Finish: Satin clear (silver), bronze or bright gold anodised aluminium (15µm). Fixing: Screw fix. Zinc plated, cross recess head S.T. screws supplied. Fixing holes are pre-slotted. Seal: RP303. Black EPDM or TPE. Sizes: 915mm and 1220mm maximum (between door stops). Approvals Fire Gasket flammability index less than 5 when tested to AS1530.2. Energy NCC Pt. 3.12.3.3 & J3.4. Durability Tested to over 1,000,000 operating cycles without failure. Patented.

A storm proof door bottom seal and threshold plate that is ideal where maximum weather protection is required. The RP4 multi-blade seal defies rain infiltration. Can be fitted to the square cut bottom of a door without removing the door, provided there is an existing gap of 25mm. It is quick and easy to fit to both door and sill. The sealing section is slotted for adjustment. Also available as an intumescent fire and hot smoke seal. Refer to RP4FZ. Location: Bottom of single and double butt hinged doors and sill. Min/Max Gap: 23mm to 25mm. Finish: Satin clear (silver), bronze or bright gold anodised aluminium (15µm) with anodised threshold plate (25µm). Fixing: Concealed screw fix. Zinc plated, cross recess head S.T. screws and cover strip supplied. Fixing holes are pre-slotted. Threshold plate fixing holes are pre-punched and countersunk. Seal: RP404, RP404a and RP404b. Grey PVC. Sizes: Available in stock lengths. Approvals Access & Mobility NZ: NZ BC Compliance Doc D1/AS1 1.3.2. Fire Approved UK/EU: Approved Document M. Energy NCC Pt. 3.12.3.3 & J3.4.

An adjustable, automatic door bottom seal that is spring loaded to lift clear of the floor when the door is opened. It is acoustically designed, featuring silicon gaskets for medium temperature smoke and fire door applications. Operated automatically by pressure against the door jamb or stop on its adjustable strike. Location: Face mounted or semi-morticed into the bottom of solid core single and double butt hinged doors. The RP35Si can also be face mounted to the bottom of metal doors. Min/Max Gap: 3mm to 13mm. Finish: Satin clear (silver) or bronze anodised aluminium (15µm). Fixing: Concealed screw fix. Zinc plated, cross recess head S.T. screws, colour matched escutcheon plates and cover strip supplied. Fixing holes are pre-slotted. Seal: RP308Si. Grey silicon rubber (SE). Sizes: 1220mm, 1070mm, 920mm, 820mm, 600mm, 380mm to 295mm(min). Seals cut back to exact size. Approvals ANSI/BHMA A156.22 Acoustic AUS/NZ: NCC Spec. F5.5. UK/EU: Approved Document E. Rated to BS EN ISO 717.1. Fire AUS/NZ: NCC Spec. C3.4. AS1530.4 & AS/NZS 1905.1. NZ BC Compliance Doc. C/AS1 6.19.2 & App. C6.1.1. UK/EU: Approved Document B. BS 476 Pt. 20 & 22 (similar to BS EN 1634-1). FRL & FRR-/240/60 and FD240.Fire Approved Gasket flammability index 1 when tested to AS1530.2. Smoke NCC Spec. C3.4. AS1530.7 & BS EN 1634-3. Meets smoke leakage rates specified in AS6905 & EN 13501-2 “Sa”, “Sm”. Energy NCC Pt. 3.12.3.3 & J3.4. Design for Access and Mobility High efficiency mechanism to assist with the closing force requirements detailed in AS1428.1. Durability Tested to over 1,000,000 operating cycles without failure. Patented, Registered Design.

An adjustable, automatic door bottom seal which is spring loaded to lift clear of the floor when the door is opened. Operated automatically by pressure against the door stop on its adjusting screw and incorporates concealed fixings. The RP60 is self levelling and can be used in conjunction with Raven threshold plates such as the RP13 and RP82. Location: Face mounted on the bottom of single and double butt hinged doors. Min/Max Gap: 3mm to 15mm. Finish: Satin clear (silver), bronze or bright gold anodised aluminium (15µm). Fixing: Concealed screw fix. Zinc plated, cross recess head S.T. screws and cover strip supplied. Fixing holes are pre-slotted. Seal: RP460. Black TPE. Sizes: 915mm maximum (between door stops). Unit cuts back to 450mm (min). Approvals Fire AUS/NZ: NCC Spec. C3.4. AS1530.4 & AS/NZS 1905.1. NZ BC Compliance Doc. C/AS1 6.19.2 & App. C6.1.1. UK/EU: Approved Document B. BS 476 Pt. 20 & 22 (similar to BS EN 1634-1). FRL & FRR-/240/30 and FD240.Fire Approved Energy NCC Pt. 3.12.3.3 & J3.4. Design for Access and Mobility High efficiency mechanism to assist with the closing force requirements detailed in AS1428.1. Durability Tested to over 500,000 operating cycles without failure. Patented.

Raven RP120 RP120 is a co-extruded PVC acoustic smoke seal that is discreetly located in the protected corners of rebated timber or steel door and window frames. RP120 is now available in white as well as black to blend in with frames and is suitable for both new and retrofit projects. Can be used in conjunction with Raven door bottom seals and astragals and threshold plates. Location: Around metal or timber rebated frames of single and double butt hinged doors and windows. Min/Max Gap: 3mm to 5.5mm. Fixing: Aggressive self adhesive backing tape on both sides of the carrier. Note: Contact surface must be clean, smooth and if painted, well cured. Self adhesive seals will not adhere to oiled or alkyd finishes or to easy clean wash and wear paint surfaces. Seal: Black or white co-extruded rigid and flexible flame retardant PVC. Sizes: Available in door set sizes. Approvals UL Cert. GVYI.R37913. Acoustic AUS/NZ: NCC Spec. F5.5. UK/EU: Approved Document E. Rated to BS EN ISO 717.1. Fire AUS/NZ: NCC Spec. C3.4. AS1530.4 & AS/NZS 1905.1. NZ BC Compliance Doc. C/AS1 6.19.2 & App. C6.1.1. UK/EU: Approved Document B. (Tests above are similar to BS EN 1634-1 & BS 476 Pt. 20 & 22). FRL & FRR-/240/30 and FD240.Fire Approved Smoke NCC Spec. C3.4. AS1530.7 & BS EN 1634-3. Meets smoke leakage rates specified in AS6905 & EN 13501-2 “Sa”, “Sm”. Energy NCC Pt. 3.12.3.3 & J3.4.